How to bind and setup FRX Pro
Turn on the gimbal and MōVI Controller that the FRX Pro's are going to link.
The FRX Pro's status light will turn white during boot and standby.
If the FRX Pro modules are already bound and connected to a gimbal and controller which are running, the status lights will turn green after a few seconds.
If the status light remains white, press the bind button of the FRX Pro connected to the controller, wait one second, then press the bind button of the other FRX Pro.
Both FRX Pro's status lights will begin flashing white and the modules will initiate the binding procedure.
Once a data connection is established both the status lights on the FRX Pro modules will turn green.
If the FRX Pro modules cannot establish a connection the status lights will turn red and then return to their standby state.
Repeat the binding steps above if a binding attempt fails.
To use the MōVI Controller with FRX Pro you must change the MōVI Controller's Radio Type setting to 'USB'
To access this setting navigate to the MōVI Controller's Radio Config menu and use the Menu Set knob to change the Radio Type to 'USB'
Once the setting has been changed, 'Write' it to the MōVI Controller's memory by selecting the 'Write' field on the next line and pressing the Menu Set knob.
To use the old MC-RX with this MōVI Controller, you must set the Radio Type back to 'Internal'
Use of FRX Pro requires a MoVI Controller that is updated to v4.1.X or newer.
Use of FRX Pro requires a MoVI gimbal that is updated to v2.0.X Blackjack or newer.
Running dual MōVI Controllers using FRX Pro is not possible, due to the FRX Pro's large power draw it consumes the power from both COM ports on the GCU. Please use the MōVI Controller Receivers when attempting to use two MōVI Controllers.
How to mount FRX Pro
Install a FRX Pro module to your gimbal using the Pop-n-Lock dovetail and a Pop-n-Lock mounted to the pan axis of your gimbal. See the diagram below for suggested mounting areas on your gimbal.
If necessary you can update the orientation of the Pop-n-Lock dovetail to make adjust the orientation of the FRX Pro module.
Alternatively you can utilize the zip-tie features machined into the front face of FRX Pro to secure it to the mounting surface.
Mount the other FRX Pro module to your MōVI Controller setup.
We suggest using a Screw Mount Pop-n-Lock kit to utilize one of the many 1/4-20" mounting location on the MōVI Controller and most monitors.
Unplug any devices from COM1 of the gimbal's GCU.
When using FRX Pro you will no longer need the older MC-RX's. These can be removed from the gimbal.
Use one of the COM Cables provided in the kit to connect the FRX Pro's UART port to the COM1 port of your gimbal.
For power, connect the other FRX Pro module to an external power supply, such as a V-Lock battery using the FRX Pro D-Tap Power cable.
For signal, connect the FRX Pro to the MōVI Controller using the USB Cable provided in the kit.
Ensure you have plugged the USB Cable into the bottom USB port on the MōVI Controller.
How to update FRX Pro
FRX Pro's ship with the latest stable FW preloaded onto each module so no updating is necessary before use!
To update the FRX Pro module you will need to download the latest FRX Pro FW to a PC.
You can find the latest FW packages on the FRX Pro's support page.
Connect the USB A-C cable to your computer then plug in the FRX Pro module while holding down its Bind button.
The status light will turn blue indicating it is in FW Update Mode.
Open the configurator bundled with the FRX Pro FW and connect to the correct COM port using the drop down menu at the top of the configurator.
If you are using a Mac select the port named 'tty.ubsbmodemXXXXXX'.
With the correct COM port selected, choose the new firmware file using the Browse button.
The name of the file will be FRX_Pro_x-x-x_xxxxxxxx.enc.
Click the Load button to begin the FW load process. After a few seconds, the new firmware file will be sent to the FRX Pro module. Wait for the progress to reach 100%.
If FW load fails make sure you are in the FW Update Mode.
FRX Pro modules are updated individually; this means each module must be updated when a FW update is released.
FRX Pro's power and baud rate can be adjusted when necessary, for instruction review the steps detailed out below.
To enter Configuration mode simply connect an FRX to a PC using a USB A-C cable.
Do not press the bind button to enter the Configuration mode.
Open the configurator bundled with the FRX Pro FW and connect to the correct COM port using the drop down menu at the top of the configurator.
With the COM port selected, press the Start Configuration Mode button.
The Power Level and Aux Baud Rate can now be adjusted and written to the FRX Pro module using the Write Configuration button.
Always use an Aux baud Rate of '111111' when using FRX Pro with the MōVI family of gimbals.
To reset the FRX Pro module to defaults select the Default Configuration button in the configurator.
Users may configure the FRX Pro to use a subset of its available frequency range. This setting is not exposed within the configurator application but may be changed through serial commands on the radio. The following procedure explains how to connect to the FRX Pro with a serial connection and change the frequencies used by the radio.
The procedure below must be completed on both radios of a FRX Pro pair.
Do not run the bind process after changing the frequency range. The bind process will reset the frequency to the default full range of 902 Mhz - 928 Mhz.
Connect your FRX Pro to your PC using a USB-C cable.
Type +++ in the blank terminal window, press enter, then wait five seconds. The radio should reply "NO CARRIER".
Enter ATS180=<Zone#> where <Zone#> is the zone ID noted in Step 6. For example, to use Zone 5, type ATS180=5.
The last digit in ATS180 is the segment number. If you are choosing a Zone with Segment 0, you will not need to change the segment number. If you want to choose a Zone with Segment 1, type ATS181=<Zone#>.
Enter AT&W.
Unplug the radio and repeat for the second FRX Pro.
For the latest MōVI Controller FW, please visit the page.
Download and install a terminal client like or .
For Windows, open the Device Manager. Then, expand Ports (COM and LPT). Note the COM port number for the FRX Pro. For example, in the screenshot below, the FRX Pro is on COM11.
For macOS, open the Terminal application. Enter ls /dev/tty.* to view a list of connected devices and their assigned ports.
Open the terminal client from Step 1 and connect to the COM port from Step 3 with speed 9600. If you are using Putty, select Serial. Next, enter the COM port number. Then confirm the speed is 9600. If you're using CoolTerm, go to Connections>Options, and create a connection to the COM port from Step 3 in the Port drop-down window with a speed of 9600. Click OK. On the Main CoolTerm screen, click connect at the top to connect to the port.
Enter ATS180 /? to view a list of available frequency zones. Note the zone number you wish to use.
Item
1. COM Port Drop down Menu
2. Read Configuration Button
3. Default Configuration Button
4. Write Configuration Button
5. Power Level Setting
6. Aux Baud Rate Setting
7. FRX FW Version
8. FW File Selection Button
9. FW Load Button
