MoVI Pro
345 x 345 x 432mm (L*W*H)
Camera Cage
196 x 200 x 175mm (L*W*H)
Pan Range of Motion
±360º Continuous Rotation
Tilt Range of Motion
+165º to -90º
Roll Range of Motion
+/-60º
Max Tilt/Roll Rate
360º/s
Max Pan Rate
360º/s
Weight
2.65kg
Max Payload
6.80kg
Max Operating Speed*
100kph
*Dependent on payload
Operating Temperatures
-20° to 50°C
Ingress Protection (IP)
IP52 (5) Dust Protected (2) Water spray @ <15º
Mounting System
Freefly Toad In The Hole (TITH) Quick Release
Data Logging Rate
5, 10, and 25 Hz
Connections
Bluetooth Low Energy v4.2 and 2.4GHz Custom FHSS Radio
Max Pan Motor Torque
0.72 N m
Max Tilt/Roll Motor Torque
0.51 N m
Motor Type
Direct-drive 3 phase Brushless
Data Storage
microSD
Port Types
GCU ports -
COM1, 12V, COM 2
TSU Ports -
LTC Timecode In/Out, EXP, CANbus + Battery Voltage, CAM,
12-14V CAM, 12V AUX,
F,I,Z, USB Type C
SL4 BATTERY
Nominal Battery Voltage
21.6V
Min - Max Battery Voltage
18 - 25.2V
Capacity (Ah)
4.1
Capacity (Wh)
86.4
Ambient Temperature
-20 °C to 50 °C
Battery Cell Temperature
10 °C to 50 °C
Charging Temp
0 °C to 50 °C
Weather
Moderate rain (~3 mm per minute)
Drop rating
1 meter
USB Power Delivery
60 Watts (Up to 3 A at the following voltages: 20, 15, 12, 9, 5)
Cell Chemistry
Lithium-Ion
Cell Type
SL4 : Lishen LR2170SF
Max Continuous Current (10 s)
SL4 : 13.5A
Max Peak Current (1 s)
SL4 : 20 A
Mass
SL4 : 600g
ORIGINAL MÅŒVI PRO BATTERY
Nominal Battery Voltage
22.2V
Max Battery Voltage
25.2V
Battery Size
1800 mAh
Cells
6 Cells
Max Battery Quantity
2 Battery
Min Battery Quantity
1 Battery
Max Peak Discharge Rate (Per Pack)
20-25A
For airline travel and shipping regulations, check the specifications battery under SuperLight Batteries in this Wiki.
GCU Layout:
Power Button * Push (ON) * Hold (OFF)
Back Button
Forward Button
Select Option (-)
Select Option (+)
microSD Card Slot
GCU Connections:
COM 1
12V
COM 2
TILT STAGE UNIT (TSU)
TSU CONNECTIONS
TC
EXP
CAN
CAM
12-14V CAM
12V AUX
Focus
Iris
Zoom
USB C DRP
All connector pinouts are shown looking into the function side of the connectors on the GCU and TSU, unless stated otherwise.
GIMBAL CONTROL UNIT:
Connector
Type
Pin-Out
COM 1
JST GH 6-pin
Insert Image of Pin-Out -from front (2D)
1 - GND 4 - UARTn_RX 2 - +5V 5 - UARTn_CTS 3 - UARTn_TX 6 - UARTn_RTS
12V
Female P-TAP
Insert Image of Pin-Out -from front (2D)
+ 12V PTAP V+ - 12V PTAP GND
COM 2
JST GH 6-pin
Insert Image of Pin-Out -from front (2D)
1 - GND 4 - UARTn_RX 2 - +5V 5 - UARTn_CTS 3 - UARTn_TX 6 - UARTn_RTS
TILT STAGE UNIT
Connector
Type
Pin-Out
TC (LTC Timecode)
3.5mm Jack
Insert Image of Pin-Out
(Shown from Function Side of the male 3.5mm Jack)
1 - (Base, Mic) - LTC IN 2 - (Ring, Gnd) - GND 3 - (Ring, Right) - SYNC IN 4 - (Tip, Left) - LTC OUT
EXP (Expansion)
JST ZPH 10 Pin
Insert Image of Pin-Out
1 - GND 6 - RxD1/Rx+ 2 - +12V 7 - TxD2/Tx+ 3 - GND 8 - RxD2/Rx- 4 - +5V 9 - GPI/UART RX 5 - TxD1/Tx- 10 - GPO/UART TX
CAN (CANbus)
Molex MicroFit RA 4 Pin
Insert Image of Pin-Out
1 - GND 3 - CAN H 2 - +V Bat 4 - CAN L
CAM (Camera)
Molex MicroFit RA 8 Pin
Insert Image of Pin-Out
1 - GND 5 - LANC Power 2 - +5V 6 - LANC Signal 3 - RxD 7 - GPO/UART TX 4 - TxD 8 - GPI/UART RX
12-14V CAM (Camera Power)
Female P-TAP
Insert Image of Pin-Out -from front (2D)
+ 14V PTAP V+ - 14V PTAP GND
12V AUX (Auxiliary Power)
Female P-TAP
Insert Image of Pin-Out -from front (2D)
+ 12V PTAP V+ - 12V PTAP GND
F (Focus Motor)
Molex MicroFit RA 6 Pin
Insert Image of Pin-Out
1 - Motor A 4 - GND 2 - Motor B 5 - Encoder A 3 - +5V 6 - Encoder B
I (Iris Motor)
Molex MicroFit RA 6 Pin
Insert Image of Pin-Out
1 - Motor A 4 - GND 2 - Motor B 5 - Encoder A 3 - +5V 6 - Encoder B
Z (Zoom Motor)
Molex MicroFit RA 6 Pin
Insert Image or Pin-Out
1 - Motor A 4 - GND 2 - Motor B 5 - Encoder A 3 - +5V 6 - Encoder B
USB Port
USB Type C DRP (Source and Sink 5V)
Gimbal Control Unit (GCU)
