Specification

DIMENSIONS

MoVI Pro

345 x 345 x 432mm (L*W*H)

Camera Cage

196 x 200 x 175mm (L*W*H)

MECHANICAL

Pan Range of Motion

±360º Continuous Rotation

Tilt Range of Motion

+165º to -90º

Roll Range of Motion

+/-60º

Max Tilt/Roll Rate

360º/s

Max Pan Rate

360º/s

Weight

2.65kg

Max Payload

6.80kg

Max Operating Speed*

100kph

*Dependent on payload

Operating Temperatures

-20° to 50°C

Ingress Protection (IP)

IP52 (5) Dust Protected (2) Water spray @ <15º

Mounting System

Freefly Toad In The Hole (TITH) Quick Release

ELECTRONICS

Data Logging Rate

5, 10, and 25 Hz

Connections

Bluetooth Low Energy v4.2 and 2.4GHz Custom FHSS Radio

Max Pan Motor Torque

0.72 N m

Max Tilt/Roll Motor Torque

0.51 N m

Motor Type

Direct-drive 3 phase Brushless

Data Storage

microSD

Port Types

GCU ports -

COM1, 12V, COM 2

TSU Ports -

LTC Timecode In/Out, EXP, CANbus + Battery Voltage, CAM,

12-14V CAM, 12V AUX,

F,I,Z, USB Type C

BATTERY SPECS

SL4 BATTERY

Nominal Battery Voltage

21.6V

Min - Max Battery Voltage

18 - 25.2V

Capacity (Ah)

4.1

Capacity (Wh)

86.4

Ambient Temperature

-20 °C to 50 °C

Battery Cell Temperature

10 °C to 50 °C

Charging Temp

0 °C to 50 °C

Weather

Moderate rain (~3 mm per minute)

Drop rating

1 meter

USB Power Delivery

60 Watts (Up to 3 A at the following voltages: 20, 15, 12, 9, 5)

Cell Chemistry

Lithium-Ion

Cell Type

SL4 : Lishen LR2170SF

Max Continuous Current (10 s)

SL4 : 13.5A

Max Peak Current (1 s)

SL4 : 20 A

Mass

SL4 : 600g

ORIGINAL MŌVI PRO BATTERY

Nominal Battery Voltage

22.2V

Max Battery Voltage

25.2V

Battery Size

1800 mAh

Cells

6 Cells

Max Battery Quantity

2 Battery

Min Battery Quantity

1 Battery

Max Peak Discharge Rate (Per Pack)

20-25A

For airline travel and shipping regulations, check the specifications battery under SuperLight Batteries in this Wiki.

GCU and TSU Layouts

GCU Layout:

  1. Power Button * Push (ON) * Hold (OFF)

  2. Back Button

  3. Forward Button

  4. Select Option (-)

  5. Select Option (+)

  6. microSD Card Slot

GCU Connections:

  1. COM 1

  2. 12V

  3. COM 2

TILT STAGE UNIT (TSU)

TSU CONNECTIONS

  1. TC

  2. EXP

  3. CAN

  4. CAM

  5. 12-14V CAM

  6. 12V AUX

  7. Focus

  8. Iris

  9. Zoom

  10. USB C DRP

CONNECTORS AND PINOUTS

All connector pinouts are shown looking into the function side of the connectors on the GCU and TSU, unless stated otherwise.

GIMBAL CONTROL UNIT:

Connector

Type

Pin-Out

  1. COM 1

JST GH 6-pin

Insert Image of Pin-Out -from front (2D)

1 - GND 4 - UARTn_RX 2 - +5V 5 - UARTn_CTS 3 - UARTn_TX 6 - UARTn_RTS

  1. 12V

Female P-TAP

Insert Image of Pin-Out -from front (2D)

+ 12V PTAP V+ - 12V PTAP GND

  1. COM 2

JST GH 6-pin

Insert Image of Pin-Out -from front (2D)

1 - GND 4 - UARTn_RX 2 - +5V 5 - UARTn_CTS 3 - UARTn_TX 6 - UARTn_RTS

TILT STAGE UNIT

Connector

Type

Pin-Out

  1. TC (LTC Timecode)

3.5mm Jack

Insert Image of Pin-Out

(Shown from Function Side of the male 3.5mm Jack)

1 - (Base, Mic) - LTC IN 2 - (Ring, Gnd) - GND 3 - (Ring, Right) - SYNC IN 4 - (Tip, Left) - LTC OUT

  1. EXP (Expansion)

JST ZPH 10 Pin

Insert Image of Pin-Out

1 - GND 6 - RxD1/Rx+ 2 - +12V 7 - TxD2/Tx+ 3 - GND 8 - RxD2/Rx- 4 - +5V 9 - GPI/UART RX 5 - TxD1/Tx- 10 - GPO/UART TX

  1. CAN (CANbus)

Molex MicroFit RA 4 Pin

Insert Image of Pin-Out

1 - GND 3 - CAN H 2 - +V Bat 4 - CAN L

  1. CAM (Camera)

Molex MicroFit RA 8 Pin

Insert Image of Pin-Out

1 - GND 5 - LANC Power 2 - +5V 6 - LANC Signal 3 - RxD 7 - GPO/UART TX 4 - TxD 8 - GPI/UART RX

  1. 12-14V CAM (Camera Power)

Female P-TAP

Insert Image of Pin-Out -from front (2D)

+ 14V PTAP V+ - 14V PTAP GND

  1. 12V AUX (Auxiliary Power)

Female P-TAP

Insert Image of Pin-Out -from front (2D)

+ 12V PTAP V+ - 12V PTAP GND

  1. F (Focus Motor)

Molex MicroFit RA 6 Pin

Insert Image of Pin-Out

1 - Motor A 4 - GND 2 - Motor B 5 - Encoder A 3 - +5V 6 - Encoder B

  1. I (Iris Motor)

Molex MicroFit RA 6 Pin

Insert Image of Pin-Out

1 - Motor A 4 - GND 2 - Motor B 5 - Encoder A 3 - +5V 6 - Encoder B

  1. Z (Zoom Motor)

Molex MicroFit RA 6 Pin

Insert Image or Pin-Out

1 - Motor A 4 - GND 2 - Motor B 5 - Encoder A 3 - +5V 6 - Encoder B

  1. USB Port

USB Type C DRP (Source and Sink 5V)

Last updated